BURN BARRIER 50-50a Foam Kote is a VOC compliant, water-based intumescent fire retardant paint, manufactured expressly for the thermal protection.
Burn Barrier 50-50A Product Description?
BURN BARRIER 50-50 Foam Kote is a VOC compliant, water base intumescent fire retardant paint,manufactured expressly for the thermal protection of polyurethane foam insulation. This product is designed for use on interior polyurethane foam surfaces were it is either necessary or desirous to reduce the burn through and flame spread rating characteristics of the foam.
It dries quickly to a flat matte finish, having the appearance of a conventional flat paint. In the presence of heat or flame, the coating puffs up (intumescent) and forms a thick sponge-like cellular foam layer. This foam layer insulates the foam substrate from flames, reduces the penetration of heat, prolongs heat transfer and burn through and reduces the surface flame spread characteristics of the foam. These combined characteristics prolong the structural collapse of the foam composite assembly for both 2 pound and 1/4 pound sprayed foams.
Attic& Crawl Space Test Results:
For 1/2 pound foam; exceeds current “Flame Out the Front” and “Burn Through” criteria accepted by the International Code Council (ICC), and exceeds currently proposed new criteria.
For 2 pound polyurethane foam; exceeds current “flame out the Front” and “Burn Through” criteria accepted by the ICC*, and exceeds currently proposed flame Out the Front criteria.
*ICC is a membership association dedicated to building safety and fire prevention, developing the codes used to construct residential and commercial buildings, including homes and schools. Most U.S. cities, counties and states that adopt codes choose the I-Codes developed by the ICC.
ASTM E-84 Surface Flame Spread Results for BURN BARRIER 50-50a Foam Kote?
Class A surface flame spread of 20, tested on 2 pound, Class II Polyurethane Foam in ASTM E-84 test. Complete Test Reports, available upon request.
Can be applied directly to fully cured polyurethane foam surfaces. If the surface is cut or shaved, exposing the foam cells, we recommend a coat of Burn Barrier 3003 water base primer, prior to the application of the Burn Barrier No. 50-50 Foam Kote. All surface preparation should be carried out in accordance with good painting practices. Remove all loose, peeling or powdery existing paint from the surface. All dirt, grease, oil, wax, and other foreign matter MUST be removed with a detergent, rinse surface thoroughly with clear water, and allow to dry.
BURN BARRIER 50-50a Foam Kote Application?
Burn Barrier No. 50-50 Foam Kote can be applied by brush, roller, airless or conventional heavyduty spray equipment. Stir thoroughly and apply at approximately 200 square feet per gallon per coat, two coats are necessary to achieve the performance characteristics referenced. If thinning is required, use WATER only. Do not exceed 1/2 pint per gallon. Do not apply in temperatures below 50F (10C).
Coverage Rate to achieve performance characteristics referenced below:
100 sq. ft. / gal., applied in 2 coats of ~ 200 sq. ft. / gal. each coat See complete reports, available upon request.
Under normal conditions, dries to touch in 1 – 2 hours, can be recoated in 2 – 4 hours.
For thinning, use only clean water, maximum 1/2 pint per gallon. For equipment clean-up use warm soapy water.
Available in white, off-white, and pastel shades, or may be field tinted with most universal tinting colorants. Tinting colorants should not exceed 2 fluid ounces per gallon.
Standard packaging, 1 gallon, 5 gallon, and 55 gallon containers.
Do not take internally. Close container after each use. Protect from freezing.
FIRE HAZARD CLASSIFICATION:
Attic & Crawl Space Test Results: (ICCES Accepted Alternate Test Protocol For IGNITION BARRIER)
Polyurethane foam insulated assemblies coated with Burn Barrier No. 50-50 Foam Kote.
For 1/2 pound foam
Flame out the Front – 2.6 minutes versus fiberglass insulated assembly of 1.9 minutes. Burn Through 16.8 minutes versus fiberglass insulated assembly of 9.7 minutes.
Flame out the Front – 6.1 minutes versus plywood covered polyurethane wall and fiberglass insulated ceiling assembly of 3.3 minutes. Burn Through >50 minutes versus plywood covered polyurethane wall and fiberglass insulated ceiling assembly of 25.1 minutes.
For 2 pound foam
Flame out the front – 3.4 minutes versus fiberglass insulated assembly of 1.9 minutes. Burn Through 24.6 minutes versus fiberglass insulated assembly of 9.7 minutes.
Flame out the front – 7.5 minutes versus plywood covered polyurethane wall and fiberglass insulated ceiling assembly of 4.2 minutes.
Complete Reports supporting above data, available upon request.
KEEP OUT OF REACH OF CHILDREN READ MSDS BEFORE OPENING CONTAINERS
Information provided herein is based on information available at the time of printing. However, we make no guarantee or warranty that this product meets or complies with any federal, state, local or foreign government code requirements. As we cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used, we accept no responsibility for results obtained by the application of this information or the safety and suitability of our products, either alone or in combination with other products. Users are advised to make their own tests to determine the safety and suitability of each such product or product combination for their own purposes. We sell our products without warranty or guarantee, and buyers and users assume all responsibility and liability for loss or damage arising from the use of this information, handling and use of our products, whether used alone or in combination with other products.